Compressive strength of three-dimensionally reinforced carbon/carbon compositeHATTA, Hiroshi; TANIGUCHI, Keisuke; KOGO, Yasuo et al.Carbon (New York, NY). 2005, Vol 43, Num 2, pp 351-358, issn 0008-6223, 8 p.Article

Interfacial shear strength of C/C compositesFURUKAWA, Yuko; HATTA, Hiroshi; KOGO, Yasuo et al.Carbon (New York, NY). 2003, Vol 41, Num 9, pp 1819-1826, issn 0008-6223, 8 p.Article

Analysis of gas leakage through C/C compositesHATTA, Hiroshi; SHIBUYA, Kazunari; NISHIYAMA, Yuichi et al.Carbon (New York, NY). 2003, Vol 41, Num 14, pp 2831-2838, issn 0008-6223, 8 p.Article

The effect of adhesive thickness on tensile and shear strength of polyimide adhesiveNAITO, Kimiyoshi; ONTA, Mutsumi; KOGO, Yasuo et al.International journal of adhesion and adhesives. 2012, Vol 36, pp 77-85, issn 0143-7496, 9 p.Article

The effect of specimen width on the bending strength of ceramic matrix textile compositesKOBAYASHI, Satoshi; MOROHOSHI, Atsushi; WAKAYAMA, Shuichi et al.Composites. Part B, Engineering. 2005, Vol 36, Num 4, pp 359-364, issn 1359-8368, 6 p.Article

Enhancement of internal friction of carbon-carbon composites by selective oxidationKOGO, Yasuo; IIJIMA, Yoshie; IGATA, Naohiro et al.Journal of alloys and compounds. 2003, Vol 355, pp 154-160, issn 0925-8388, 7 p.Conference Paper

Rapid and three-dimensional nanoimprint template fabrication technology using focused ion beam lithographyTANIGUCHI, Jun; KOGA, Kentaro; KOGO, Yasuo et al.Microelectronic engineering. 2006, Vol 83, Num 4-9, pp 940-943, issn 0167-9317, 4 p.Conference Paper

Tensile strength of carbon/carbon compositesHATTA, Hiroshi; AOI, Tatsuji; KAWAHARA, Itaru et al.JSME international journal. Series A, Solid mechanics and material engineering. 2003, Vol 46, Num 3, pp 290-296, issn 1344-7912, 7 p.Conference Paper

Classification of microstructural evolution during large strain high Z deformation of a 0.15 carbon steelNARAYANA MURTY, S. V. S; TORIZUKA, Shiro; NAGAI, Kotobu et al.Scripta materialia. 2005, Vol 52, Num 8, pp 713-718, issn 1359-6462, 6 p.Article

Grain boundary diffusion controlled ultrafine grain formation during large strain-high Z deformation of coarse (200 μm) grained ultra-low carbon steelNARAYANA MURTY, S. V. S; TORIZUKA, Shiro; NAGAI, Kotobu et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2007, Vol 457, Num 1-2, pp 162-168, issn 0921-5093, 7 p.Article

Internal friction of carbon-carbon composites at elevated temperaturesKOGO, Yasuo; IIJIMA, Yoshie; IGATA, Naohiro et al.Journal of alloys and compounds. 2003, Vol 355, pp 148-153, issn 0925-8388, 6 p.Conference Paper

Extraordinary deposition rate of diamond-like carbon film using HIPIMS technologyHIRATSUKA, Masanori; AZUMA, Akiyoshi; NAKAMORI, Hideki et al.Surface & coatings technology. 2013, Vol 229, pp 46-49, issn 0257-8972, 4 p.Conference Paper

Fabrication of large sintered pellets of Sb-doped n-type Mg₂Si using a plasma activated sintering methodHAYATSU, Yusuke; IIDA, Tsutomu; SAKAMOTO, Tatsuya et al.Journal of solid state chemistry (Print). 2012, Vol 193, pp 161-165, issn 0022-4596, 5 p.Article